Vertical System
Characteristic |
TDS5034B |
TDS5054B |
TDS5104B |
---|---|---|---|
Input Channels |
4 | ||
Analog Bandwidth (-3dB) 5mV/div - 1V/div |
350MHz |
500MHz |
1GHz |
Calculated Rise Time 5mV/div (typical) |
1.15ns |
800ps |
300ps |
Hardware Bandwidth Limits |
150MHz or 20MHz | ||
Input Coupling |
AC, DC, GND | ||
Input Impedance, 1MΩ |
±1% | ||
Input Impedance, 50Ω |
±1% |
±2.5% | |
Input Sensitivity, 1MΩ |
1mV/div to 10V/div | ||
Input Sensitivity, 50Ω |
1mV/div to 1V/div | ||
Vertical Resolution |
8bits (>11bits w/ averaging) | ||
Max Input Voltage, 1MΩ |
150V CAT I, ≤400V peak. Derate at 20dB/decade to 9VRMS above 200kHz | ||
Max Input Voltage, 50Ω |
5V RMS with peaks < ±30V |
<100mV/div <1VRMS ≥100mV/div <5VRMS | |
DC Gain Accuracy |
1.5% with offset set to 0V | ||
Offset Range, 1MΩ |
1mV/div - 99.5mV/div ±1V 100mV/div - 1V/div ±10V 1.01V/div - 10V/div ±100V | ||
Offset Range, 50Ω |
1mV/div - 99.5mV/div ±1V 100mV/div - 1V/div ±10V |
1mV/div - 50mV/div ±0.5V 50.5mV/div - 99.5mV/div ±0.25V 100mV/div - 500mV/div ±5V 505mV/div - 1V/div ±2.5V | |
Channel-to-Channel Isolation for Any Two Channels at Equal Vertical Scale |
≥100:1 at ≤100MHz and ≥30:1 at >100MHz up to the rated bandwidth |
Timebase System
Characteristic |
Description |
---|---|
Timebase Range |
200ps/div to 1000s/div |
Timebase Delay Time Range |
(s/div × 10) to 1000s |
Channel-to-Channel Deskew Range |
±75ns |
Timebase Accuracy |
15 ppm |
Delta Time Measurement Accuracy |
(0.06/sample rate + 15 ppm × |Reading|)RMS |
Trigger Jitter (RMS) |
8psRMS (typical) |
Long-term Sample Rate and Delay Time Accuracy |
±15 ppm over any ≥1ms interval |
Acquisition System
Characteristic |
TDS5034B |
TDS5054B / TDS5104B |
---|---|---|
Real-time Sample Rates | ||
1 Channel (max) |
5GS/s | |
2 Channels (max) |
2.5GS/s | |
3-4 Channels (max) |
1.25GS/s | |
Equivalent Time Sample Rate (max) |
250GS/s | |
Maximum Record Length per Channel with Standard Memory |
8M/4M/2M |
16M/8M/4M |
With Opt. 3M |
16M/8M/4M |
NA |
Maximum Duration at Highest Real-time Resolution (1 ch)
Characteristic |
TDS5034B |
TDS5054B / TDS5104B |
---|---|---|
Time Resolution (single shot) |
200ps (5GS/s) | |
Max Duration with Standard Memory |
1.6ms |
3.2ms |
Max Duration with Opt. 3M |
3.2ms |
NA |
Acquisition Modes
Characteristic |
Description |
---|---|
FastAcq Acquisition |
FastAcq optimizes the instrument for analysis of dynamic signals and capture of infrequent events. Maximum FastAcq waveform capture rate is 100,000 wfms/s |
Sample |
Acquire sampled values |
Peak Detect |
Captures narrow glitches (<1ns) at all real-time sampling rates |
Averaging |
From 2 to 10,000 waveforms included in average |
Envelope |
From 2 to 2 × 109 waveforms included in min-max envelope |
Hi-Res |
Real-time boxcar averaging reduces random noise and increases resolution |
Waveform Database |
Accumulates a waveform database that provides a three-dimensional array of amplitude, time, and counts |
FastFrame™ Acquisition |
Acquisition memory divided into segments; maximum trigger rate >100,000 waveforms per second |
Trigger System
Characteristic |
Description |
---|---|
Sensitivity | |
Internal DC Coupled |
0.35div DC to 50MHz increasing to 1div at rated bandwidth |
External (auxiliary input) |
400mV from DC to 50MHz increasing to 750mV at 100MHz |
Main Trigger Modes |
Auto, Normal, and Single |
Trigger Sequences |
Main, Delayed by time, Delayed by events. All sequences can include separate horizontal delay after the trigger event to position the acquisition window in time |
Standard Trigger Types |
Edge, Glitch, Runt, Window, Width, Transition Time, Timeout, Pattern, Video, State, Setup/Hold |
A Event and Delayed B Event Trigger Types | |
A Event |
All above types |
Delayed B Event |
Edge |
Communications-related Triggers (requires Option SM) |
Support for AMI, HDB3, BnZS, CMI, MLT3, and NRZ encoded communications signals. Select among isolated positive or negative one, zero pulse form, or eye patterns as applicable to standard |
Trigger Level Range | |
Any Channel |
±10divisions from center of screen |
External (auxiliary in) |
±8V |
Line |
Fixed at 0V |
Trigger Coupling |
DC, AC (attenuate <60Hz), HF reject (attenuate >30kHz) LF reject (attenuates <80kHz) Noise reject (reduce sensitivity) |
Trigger Holdoff Range |
1.5 μs to 12s maximum |
Trigger Modes
Mode |
Description |
---|---|
Edge |
Positive or negative slope on any channel or front-panel auxiliary input. Coupling includes DC, AC, noise reject, HF reject, and LF reject |
Video |
Trigger on NTSC, PAL, SECAM, analog HDTV, and nonstandard video formats |
Glitch |
Trigger on or reject glitches of positive, negative, or either polarity. Minimum glitch width is 1.0ns with 200ps resolution |
Width |
Trigger on width of positive or negative pulse either within or out of selectable time limits ranging from 1ns to 1s with 200ps resolution |
Runt |
Trigger on a pulse that crosses one threshold but fails to cross a second threshold before crossing the first again. Event can be time or logic qualified (logic on 4 channel models only) |
Window |
Trigger on an event that enters or exits a window defined by two user-adjustable thresholds. Event can be time or logic qualified (logic on 4 channel models only) |
Timeout |
Trigger on an event which remains high, low, or either, for a specified time period, selectable from 1ns to 1s with 200ps resolution |
Transition |
Trigger on pulse edge rates that are faster or slower than specified. Slope may be positive, negative, or either |
Setup/Hold |
Trigger on violations of both setup time and hold time between clock and data present on any two input channels |
Pattern |
Trigger when pattern goes false or stays true for specified period of time. Pattern (AND, OR, NAND, NOR) specified for four input channels defined as High, Low, or Don't Care |
State |
Any logical pattern of channels (1, 2, 3) clocked by edge on channel 4. Trigger on rising or falling clock edge |
Comm (requires Option SM) |
Support for AMI, HDB3, B3ZS, B6ZS, B8ZS, CMI, NRZ, and MLT3 encoded communication signals. Select among isolated positive or negative one, zero pulse form, or eye patterns as applicable to standard |
Trigger Delay by Time |
16ns to 250s |
Trigger Delay by Events |
1 to 10,000,000Events |
Waveform Measurements
Characteristic |
Description |
---|---|
Automatic Measurements |
53 of which 8 can be displayed on-screen at any one time |
Amplitude Related |
Amplitude, High, Low, Maximum, Minimum, Peak-to-Peak, Mean, Cycle Mean, RMS, Cycle RMS, Positive Overshoot, Negative Overshoot |
Time Related |
Rise Time, Fall Time, Positive Width, Negative Width, Positive Duty Cycle, Negative Duty Cycle, Period, Frequency, Delay |
Combination |
Area, Cycle Area, Phase, Burst Width |
Histogram Related |
Waveform count, Hits in box, Peak hits, Median, Maximum, Minimum, Peak-to-Peak, Mean (μ), Standard Deviation (σ), μ ± 1σ, μ ± 2σ, μ ± 3σ |
Communications Related |
Extinction Ratio (abs, %, dB), Eye Height, Eye Width, Eye Top, Eye Base, Crossing %, Jitter (P-P, RMS, 6σ), Noise (P-P, RMS), Signal/Noise Ratio, Cycle Distortion, Q-Factor |
Measurement Statistics |
Mean, Min, Max, Standard Deviation, Population |
Reference Levels |
User definable for each of the eight measurements |
Histograms |
Vertical or horizontal with linear or log scaling |
Gating |
Isolate the specific occurrence within an acquisition to take measurements on |
Cursors |
Horizontal Bars, Vertical Bars, Waveform, and Screen |
Waveform Processing/Math
Characteristic |
Description |
---|---|
Arithmetic |
Add, subtract, multiply, and divide waveforms |
Algebraic Expressions |
Define extensive algebraic expressions including waveforms, scalars, user-adjustable variables, and results of parametric measurements e.g. (Integral (Ch1-Mean(Ch1))*1.414*VAR1) |
Math Functions |
Average, Invert, Integrate, Differentiate, Square Root, Exponential, Log 10, Log e, Abs, Ceiling, Floor, Min, Max, Sin, Cos, Tan, ASin, ACos, ATan, Sinh, Cosh, Tanh |
Frequency Domain Functions |
Spectral magnitude and phase, real and imaginary spectra |
Vertical Units |
Magnitude: Linear, dB, dBm Phase: degrees, radians, group delay |
Window Functions |
Rectangular, Hamming, Hanning, Kaiser-Bessel, Blackman-Harris, Gaussian, Flattop2, Tek Exponential |
Limit Testing |
Compare live waveforms against a known “golden” reference waveform with user-defined vertical and horizontal tolerances |
Display Characteristics
Characteristic |
Description |
---|---|
Display Type |
10.4in. Liquid-crystal active-matrix color display |
Touchscreen |
Standard on TDS5054B and TDS5104B. Optional touchscreen on TDS5034B |
Display Resolution |
640 horizontal × 480 vertical pixels |
Waveform Styles |
Vectors, Dots, Intensified Samples, Variable Persistence, Infinite Persistence |
Display Format |
YT, XY, XYZ |
Color Palettes |
Individual color palettes for Record View and FastAcq/WfmDB modes include Normal, Green, Gray, Temperature, Spectral, and User Defined |
Computer System and Peripherals
Characteristic |
Description |
---|---|
Operating System |
Windows 2000 |
CPU |
Intel Celeron Processor, 2.0GHz |
PC System Memory |
512MB |
Internal Hard Disk Drive |
≥80GB capacity |
CD-RW Drive |
Side-panel CD-RW drive, ≥24x read and write speed |
Mouse |
Optical wheel mouse, USB interface |
OpenChoice Features
Characteristic |
Description |
---|---|
TekVISA |
Application Programmers Interface (API) for Windows developers. Documentation includes descriptions and samples of programming test and measurement applications on the unit in Visual BASIC, C, and C++ |
TekVISA Control (TVC) |
Active controls to make access to TekVISA easy for integration into Microsoft Windows applications |
VXI-11 Server |
An Application Programmers Interface (API) for LAN connectivity from non-Windows environments |
Plug-and-play Drivers |
Provides support to run National Instrument's LabVIEW and LabWindows on an external PC connected to a TDS5000B or on the oscilloscope itself. Instrument drivers are version specific and might not support the version of your software development tools |
IVI Drivers |
Provides support for new and existing program environments utilizing the IVI instrumentation standard, such as LabVIEW, LabWindows/CVI, MATLAB, Visual BASIC, and C/C++. Instrument drivers are version specific and might not support the version of your software development tools |
Excel and Word Toolbars |
Provides direct access to screen images, waveform data, and measurements on the oscilloscope from a toolbar in Excel and/or Word |
Report Generator |
Enables the ability to design and create customized report templates that extract the oscilloscope's waveforms, settings, measurements, and other on-screen information with a click of the mouse |
Input/Output Ports
Port |
Description |
---|---|
Auxiliary Input |
Front-panel BNC connector. Trigger level range is adjustable from +8V to -8V. The maximum input voltage is ±20V (DC + peak AC) and input resistance is ≥1.5kΩ |
Probe Compensator Output |
Front-panel pins. Amplitude 1V ±1% into a ≥10kΩ load, frequency 1kHz ±5% |
Analog Signal Output |
Rear-panel BNC connector, provides a buffered version of the signal that is attached to the Channel 3 input (4-channel models only). Amplitude: 50mV/div ±20% into a 1MΩ load, 25mV/div ±20% into a 50 Ω load. Bandwidth (typical): 100MHz into a 50 Ω load |
Auxiliary Output Levels |
Rear-panel BNC connector, provides a TTL-compatible, negative-polarity pulse when the oscilloscope triggers |
External Reference In |
Rear-panel BNC connector. 9.8MHz to 10.2MHz |
Parallel Port |
IEEE 1284, DB-25 connector |
Audio Ports |
Miniature phone jacks for stereo microphone input and stereo line output |
USB Port |
Four USB 2.0 ports allows connection or disconnection of USB keyboard and/or mouse while oscilloscope power is on |
Keyboard Port |
PS-2 compatible |
Mouse Port |
PS-2 compatible |
LAN Port |
RJ-45 connector, supports 10Base-T and 100Base-T |
Serial Port |
DB-9 COM1 port |
Video Port |
DB-15 female connector; connect a second monitor to use dual-monitor display mode. Supports basic requirements of PC99 specification and display resolutions up to 1,920 × 1,440 |
GPIB Port |
IEEE 488.2 standard, can be configured for talk/listen or controller mode |
Oscilloscope VGA Video Port |
DB-15 female connector, connect to show the oscilloscope display on an external monitor or projector |
Power Source
Characteristic |
Description |
---|---|
Power |
100 to 240VRMS ±10%, 47 to 63Hz; CAT II, or 115VRMS ±10%, 360 to 440Hz |
Power Consumption |
<220W |
Physical Characteristics
Configuration |
Benchtop |
Rackmount |
Benchtop |
Rackmount |
---|---|---|---|---|
Dimensions |
mm |
in. | ||
Height |
361 |
267 |
11.2*1 |
10.5 |
Width |
447 |
483 |
17.6 |
19 |
Depth |
288 |
231*2 |
11.35 |
9.1*2 |
Weight |
kg |
lb. | ||
Net |
11.23 |
13.49 |
24.75 |
29.75 |
Shipping |
25.63 |
— |
56.5 |
— |
Cooling | ||||
Cooling Clearance |
76mm required on left side |
3inches required on left side |
*1Does not include accessory pouch.
*2From rack mounting rear to back of instrument.
Environmental
상품의 사용후기를 적어주세요.
게시물이 없습니다
상품에 대해 궁금한 점을 해결해 드립니다.
게시물이 없습니다