 Characteristics/Specs |
|
VerticalSystem |
DPO3012 |
DPO3014 |
DPO3032 |
DPO3034 |
DPO3052 |
DPO3054 |
|
Input Channels |
2 |
4 |
2 |
4 |
2 |
4 |
|
Analog Bandwidth (-3dB) |
100 MHz |
100 MHz |
300 MHz |
300 MHz |
500 MHz |
500 MHz |
|
Calculated Rise Time
5 mV/div (typical) |
3.5ns |
3.5ns |
1.17 ns |
1.17 ns |
700 ps |
700 ps |
|
Hardware Bandwidth Limits |
20 MHz or 150 MHz |
|
Input Coupling |
AC, DC, GND |
|
Input Impedance |
1 MΩ ±1%, 75 Ω ±1%, 50 Ω ±1% |
|
Input Sensitivity Range, 1MΩ |
1 mV/div to 10 V/div |
|
Input Sensitivity Range, 75Ω,50Ω |
1 mV/div to 1 V/div |
|
Vertical Resolution |
8 bits (11 bits with Hi-Res) |
|
Max Input Voltage,1MΩ |
300 VRMS with peaks ≤±450 V |
|
Max Input Voltage, 75Ω,50 Ω |
5 VRMS with peaks ≤±20 V |
|
DC Gain Accuracy |
±1.5% with offset set to 0 V |
|
OffsetRange |
1MΩ |
50Ω, 75Ω |
|
1 mV/div to 99.5mV/div |
±1V |
±1V |
|
100mV/div to 995mV/div |
±10V |
±5V |
|
1 V/div |
±100V |
±5V |
|
1.01 V/div to 10 V/div |
±100V |
NA |
|
Channel-to-Channel Isolation
(Any Two Channels at Equal Vertical Scale) |
≥ 100:1 at ≤100 MHz and ≥ 30:1 at > 100MHz up to the rated BW |
|
Horizontal System |
All DPO3000 Models |
|
Maximum Sample Rate (all channels) |
2.5 GS/s |
|
Maximum Record Length (all channels) |
5 M points |
|
Maximum Duration of Time Captured at Highest Sample Rate (all channels) |
2 ms |
|
Time base Range (S/div) |
1 ns to 1000 s |
|
Time base Delay Time Range |
- 10 divisions to 5000 s |
|
Channel-to-Channel Deskew Range |
±100 ns |
|
Timebase Accuracy |
±10 ppm over any ≥ 1 ms interval |
|
Trigger System |
|
Main Trigger Modes |
Auto, Normal, and Single |
|
Trigger Coupling |
DC, AC, HF reject (attenuates>50 kHz), LF reject (attenuates <50 kHz), noise reject (reduces sensitivity) |
|
Trigger Holdoff Range |
20 ns to 8 s |
|
Sensitivity |
|
Internal DC Coupled |
0.4 div DC to 50 MHz, increasing to 1 div at rated bandwidth |
|
External (Auxiliary Input) |
200mV from DC to 50MHz increasing to 500mV at 250MHz |
|
Trigger Level Range |
|
Any Channel |
±8 divisions from center of screen |
|
External (auxiliary input) |
±8V |
|
Acquisition Modes |
|
Sample |
Acquire sampled values |
|
Peak Detect |
Captures narrow glitches at all real-time sampling rates |
|
Averaging |
From 2 to 512 waveforms included in average |
|
Envelope |
Min-max envelope reflecting Peak Detect data over multiple acquisitions |
|
Hi-Res |
Real-time boxcar averaging reduces random noise and increases resolution |
|
Roll |
Scrolls waveforms right to left across the screen at sweep speeds slower than or equal to 40ms/div |
|
Trigger Modes |
|
Edge |
Positive or negative slope on any channel or front panel auxiliary input. Coupling includes DC, AC, HF reject, LF reject and noise reject |
|
Pulse Width |
Trigger on width of positive or negative pulse that are >, <, = or ≠ a specified period of time |
|
Runt |
Trigger on a pulse that crosses one threshold but fails to cross a second threshold before crossing the first again |
|
Logic |
Trigger when any logical pattern of channels goes false or stays true for specified period of time. Any input can be used as a clock to look for the pattern on a clock edge. Pattern (AND, OR, NAND, NOR) specified for four input channels defined as High, Low or Don’t Care. |
|
Setup and Hold |
Trigger on violations of both setup time and hold time between clock and data present on any two input channels |
|
Rise/Fall Time |
Trigger on pulse edge rates that are faster or slower than specified. Slope may be positive, negative or either. |
|
Video |
Trigger on all lines, odd, even or all fields on NTSC, PAL and SECAM video signals |
|
Extended Video (optional) |
Trigger on 480p/60, 576p/50, 720p/30, 720p/50, 720p/60, 875i/60, 1080i/50, 1080i/60, 1080p/24, 1080p/24sF, 1080p/25, 1080p/30, 1080p/50, 1080p/60 and custom bi-level and tri-level sync video standards |
|
I2C (optional) |
Trigger on Start, Repeated Start, Stop, Missing ACK, Address (7 or 10 bit), Data or Address & Data on I2C buses up to 3.4 Mb/s |
|
SPI (optional) |
Trigger on SS, MOSI, MISO or MOSI & MISO on SPI buses up to 10.0 Mb/s |
|
CAN (optional) |
Trigger on Start of Frame, Frame Type (data, remote, error, overload), Identifier (standard or extended), Data, Identifier and Data, End of Frame, Missing ACK, or Bit Stuffing Error on CAN signals up to 1 Mb/s. Data can be further specified to trigger on ≤, <, =, >, ≥ or ≠ a specific data value. User-adjustable sample point is set to 50% by default. |
|
LIN (optional) |
Trigger on Sync, Identifier, Data, Id & Data, Wakeup Frame, Sleep Frame, Error up to 100 kb/s |
|
RS-232/422/485/UART (optional) |
Trigger on Tx Start Bit, Rx Start Bit, Tx End of Packet, Rx End of Packet, Tx Data, Rx Data, Tx Parity Error, and Rx Parity Error |
|
Trigger Delay by Time |
4 ns to 8 s |
|
Trigger Delay by Events |
1 to 9,999,999 events |
|
Waveform Measurements |
|
Cursors |
Waveform and Screen |
|
Automatic Measurements |
29, of which up to four can be displayed on screen at any one time.
Measurements include: Period, Frequency, Delay, Rise Time, Fall Time, Positive Duty Cycle, Negative Duty Cycle, Positive Pulse Width, Negative Pulse Width, Burst Width, Phase, Positive Overshoot, Negative Overshoot, Peak to Peak, Amplitude, High, Low, Max, Min, Mean, Cycle Mean, RMS, Cycle RMS, Rising Edge Count, Falling Edge Count, Positive Pulse Count, Negative Pulse Count, Area and Cycle Area. |
|
Measurement Statistics |
Mean, Min, Max, Standard Deviation |
|
Reference Levels |
User-definable reference levels for automatic measurements can be specified in either percent or units |
|
Gating |
Isolate the specific occurrence within an acquisition to take measurements on, using either the screen, or waveform cursors |
|
Waveform Math |
|
Arithmetic |
Add, subtract, multiply, and divide waveforms |
|
Math Functions |
Integrate, Differentiate, FFT |
|
FFT |
Spectral magnitude. Set FFT Vertical Scale to Linear RMS or dBV RMS, and FFT Window to Rectangular, Hamming, Hanning, or Blackman-Harris |
|
Advanced Math |
Define extensive algebraic expressions including waveforms, math functions, scalars, up to two user adjustable variables and results of parametric measurements e.g.,(Intg(Ch1–Mean(Ch1)) x 1.414 x VAR1) |
Software
|
NI LabVIEW SignalExpressTM Tektronix Edition |
A fully interactive measurement software environment optimized for the DPO3000 Series, enables you to instantly acquire, generate, analyze, compare, import and save measurement data and signals using an intuitive drag-and-drop user interface that does not require any programming.
Standard DPO3000 Series support for acquiring, controlling, viewing and exporting your live signal data. A 30-day trial period of the Full Version provides additional signal processing, advanced analysis, mixed signal, sweeping, limit testing and user-defined step capabilities. Order SIGEXPTE for permanent Full Version capability. |
|
OpenChoice®Desktop |
Enables fast and easy communication between a Windows PC and the DPO3000 Series, via USB or LAN. Transfer and save settings, waveforms, measurements and screen images. |
|
IVI Driver |
Provides a standard instrument programming interface for common applications such as LabVIEW, LabWindows/CVI, Microsoft .NET and MATLAB |
Display Characteristics
|
Display Type |
9in. (228.6mm) wide format liquid crystal TFT color display |
|
Display Resolution |
800 horizontal x 480 vertical pixels (WVGA) |
|
Waveform Styles |
Vectors, Dots, Variable Persistence, Infinite Persistence |
|
Graticules |
Full, Grid, Cross Hair, Frame, IRE and mV |
|
Format |
YT and XY |
|
Waveform Capture Rate |
Up to 50,000 wfm/s |
Input/Output Ports
|
USB 2.0 High Speed Host Port |
Supports USB mass storage devices and printers. One port available on rear-panel and one on front-panel. |
|
USB 2.0 High Speed Device Port |
Rear panel connector allows for control of oscilloscope via USBTMC or GPIB with a TEK-USB-488 |
|
LAN Port |
RJ-45 connector, supports10/100Base-T |
|
Video Out Port |
DB-15 female connector, connect to show the oscilloscope display on an external monitor or projector |
|
Auxiliary Input |
Front panel BNC connector. Input Impedance 1MΩ. Max input 300VRMS Cat II with peaks ≤±450V |
|
Probe Compensator Output |
Front panel pins. Amplitude 2.5V. Frequency 1kHz. |
|
Trigger Out |
Rear-panel BNC connector, provides a positive polarity pulse when the oscilloscope triggers |
|
Kensington Lock |
Rear-panel security slot connects to standard Kensington lock |
Power Source
|
Power Source Voltage |
85 to 265V ±10% |
|
Power Source Frequency |
45 to 440Hz (85 to 265V) |
|
Power Consumption |
120W maximum |
|
Optional TekVPI® Power Supply |
Output Voltage – 12V; Output Current – 5A; Power Consumption – 60W |
Physical Characteristics
|
Dimensions |
mm |
in. |
|
Height |
203.2 |
8 |
|
Width |
416.6 |
16.4 |
|
Depth |
137.2 |
5.4 |
|
Weight |
kg |
lbs. |
|
Net |
4.17 |
9.2 |
|
Shipping |
8.62 |
19 |
|
Rackmount Configuration |
5U |
|
Cooling Clearance |
2in.(51mm) required on left side and rear of instrument |
General Characteristics
|
Environmental |
|
|
Temperature |
|
|
Operating |
0ºC to +50ºC |
|
Non-operating |
–40ºC to +71ºC |
|
Humidity |
|
|
Operating |
High: 30ºC to 50ºC,5% to 45% Relative Humidity
Low: 0ºC to 30ºC,5% to 95% Relative Humidity |
|
Non-operating |
High: 30ºC to 50ºC,5% to 45% Relative Humidity
Low: 0ºC to 30ºC,5% to 95% Relative Humidity |
|
Altitude |
|
|
Operating |
3,000 meters (9,843 feet) |
|
Non-operating |
12,000 meters (39,370 feet) |
|
Random Vibration |
|
|
Operating |
0.31 GRMS from 5 to 500Hz, 10 minutes each axis, 3 axes, 30 minutes total |
|
Non-operating |
2.46 GRMS from 5 to 500Hz, 10 minutes each axis, 3 axes, 30 minutes total |
|
Regulatory |
|
|
Electromagnetic Compatibility |
89/336/EEC |
|
Safety |
UL61010-1,Second Edition; CAN/CSA C22.2 No. 1010.1 1992, EN61010-1:2001; IEC 61010-1:2001 | |
| | |
확대보기
Characteristics/Specs 
